Parquet shows up in more Kansas City homes than people expect. It is in mid-century houses and apartments, in dens and dining rooms that got an update a few decades ago, and sometimes under carpet where nobody has seen it in years. When the finish wears out or turns orange, the question we get is whether it can be sanded like a regular floor. The answer is yes, usually, but parquet floor refinishing is its own kind of job. The pattern that makes parquet look the way it does is exactly what makes it harder to sand well.
Why Parquet Sands Differently
On a strip or plank floor, every board runs the same direction, so the sander can follow the grain. Scratches left by the sandpaper line up with the grain and disappear into it. On parquet, the small slats in each block run in different directions, often at right angles to the slats beside them. Whatever direction the machine travels, it is going across the grain on a large part of the floor.
Sanding across the grain leaves scratches that show, especially once stain or finish goes on. Getting a clean result means changing the approach:
- Working the floor on angles rather than straight down the room, so no single set of slats takes all the cross-grain cutting.
- Stepping through the grits carefully and not skipping any, because a coarse scratch left behind on parquet will show in some blocks and not others.
- Finishing with a multi-head or orbital machine that sands in circles, which blends the scratch pattern across every direction of grain before finish goes down.
Our hardwood floor sanding guide explains the grit sequence and the machines in more detail. On parquet, that last blending pass matters even more than usual.
Loose, Hollow and Missing Blocks
Most parquet is glued down rather than nailed, often directly to concrete or to a wood subfloor. Over time some blocks let go. You can usually find them by walking the floor in socks or tapping with a knuckle: a loose block sounds hollow, rocks slightly, or clicks underfoot.
Loose blocks have to be secured before sanding. A sander passing over a loose block can catch it, chip its edges or tear it out entirely. Missing or badly damaged blocks get replaced, ideally with matching blocks pulled from a closet or other hidden spot, or with new blocks of the same species and pattern. Patterns and sizes vary, so this is something we look at on the estimate rather than assume.
If large areas are loose, that points to a problem with the adhesive or with moisture coming up from below, particularly over a slab. That needs to be understood before any money goes into the surface.
How Much Sanding Parquet Can Take
Parquet is often thinner than standard solid strip flooring, and some of it has been sanded before. A refinish removes a layer of wood, so we check the thickness at a vent or threshold before quoting. A floor with plenty of wood left can be sanded normally. A thin floor gets a lighter touch, and a floor that is close to its limit may be a better candidate for a recoat if the finish has not worn through.
Some parquet is not solid at all. Engineered parquet tiles have a thin wood veneer over a core, and those need the same caution as any engineered floor. Can engineered hardwood be refinished explains why the thickness of the top layer decides everything.
Old Adhesive Deserves Respect
Older parquet was often set in a black adhesive, and some older black adhesives contain asbestos. As long as it stays under intact flooring and is not disturbed, it is not a hazard to anyone walking on the floor. It does matter if blocks are coming up, if the floor is being removed, or if the adhesive is exposed at damaged spots. In those cases it should be tested before anyone sands or scrapes it. We will tell you if we see something that warrants a test.
Stain on Parquet
Because the grain runs every direction, stain catches light differently from block to block. That is part of parquet's character, and many people choose to keep it natural so the pattern reads clearly. If you want to stain, a test patch on your actual floor is essential, and lighter to mid tones are more forgiving than very dark ones, which make any leftover sanding mark stand out. Our wood floor staining guide covers how we test colors.
For the finish, a water-based polyurethane keeps the blocks closer to their natural color, while an oil-based finish adds an amber tone that deepens over time. Water-based or oil-based polyurethane walks through the tradeoffs.
Parquet Versus Herringbone
People sometimes use the words interchangeably, but most traditional parquet comes in square blocks made of short slats, often in a basketweave or checkerboard layout. Herringbone and chevron are laid board by board. All of them are patterned floors with grain running more than one direction, so the sanding challenges overlap. Herringbone or chevron covers those patterns and what installing them involves.
Should You Refinish or Replace It?
If the blocks are solid, mostly tight and have wood left to sand, refinishing is almost always the better value, and a well-sanded parquet floor with a fresh finish can look striking. Replacement starts to make sense when large areas are loose because of moisture, when the floor is engineered with a veneer too thin to sand, or when the pattern simply does not fit the house you want anymore. Refinish or replace lays out how we make that call.
Get Your Parquet Looked At
We refinish parquet and other patterned floors across the metro, including Kansas City, Mission Hills, Overland Park and North Kansas City. See our hardwood floor refinishing and floor repair pages for how we handle the work. Get a free estimate, and we will check the blocks, the thickness and the adhesive before telling you what the floor needs.
Get a Free Estimate
Have a floor you want looked at? We give honest, no-pressure estimates across the Kansas City metro.