Good Ol Boy installer kneeling on a subfloor beside tall windows
Hardwood Floor Guide

Why Are My Hardwood Floors Cupping or Crowning? Causes and Fixes in Kansas City

By Good Ol' Boy Hardwood Floors • • 7 min read

Run your hand across a hardwood floor and it should feel flat. If the edges of the boards stand up higher than the middles, the floor is cupping. If the middles are higher than the edges, it is crowning. Both are common in Kansas City, and both come back to the same thing: moisture moving through the wood unevenly.

The good news is that many cupped floors can be saved. The bad news is that the most common fix people reach for, sanding the floor flat right away, is the one that causes the most trouble.

Cupping: Wet Underneath

A cupped board is wetter on the bottom than on the top. The underside swells, the finished top does not swell as much, and the edges curl up. Across a whole floor that gives a washboard feel underfoot and lines of shadow at every seam when the light comes in low.

The moisture is coming from below or from the side. Common sources in Kansas City homes:

  • Crawlspaces and basements. A damp crawlspace with no vapor barrier, or an unconditioned basement in July, sends moisture up into the subfloor and the boards above.
  • Summer humidity. Our humid summers push moisture into wood, and a house running without enough air conditioning or dehumidification lets the floor take it on.
  • Leaks. Dishwashers, refrigerator water lines, sinks, toilets, and exterior doors that let rain in. Cupping that is worse in one area usually points straight at a leak.
  • Installation moisture. Wood installed before it acclimated, or laid over a subfloor that was still wet, can cup once it settles into the house.

Crowning: Often a Sanding Problem

A crowned board is high in the middle. Sometimes that comes from moisture on the surface, like a wet mop used daily for years. Far more often it comes from a cupped floor that was sanded flat while it was still wet. Sanding takes the raised edges off. Then the boards dry out, the undersides shrink back, and the board ends up lower at the edges than in the middle. The floor now has the opposite problem, and less wood left to fix it with.

Why Waiting Is Usually the Right First Step

Cupping often reverses, partly or fully, once the moisture source is fixed and the wood dries out. That can take weeks, and in some cases months. It is hard to wait when the floor looks bad, but sanding a cupped floor too early is the mistake that ruins floors that could have come back flat. Water-damaged hardwood floors covers this in more detail for floors hit by a leak or a flood.

How We Diagnose It

  • Moisture readings. A moisture meter compares the boards with each other, with the subfloor and with a dry area of the house. Readings tell us whether the floor is still wet and where the moisture is coming from.
  • The pattern. Cupping across the whole floor points to humidity or the crawlspace. Cupping in one area points to a leak nearby. Cupping along an exterior wall points to water getting in from outside.
  • What is below. If there is access, we look at the crawlspace or basement ceiling under the floor for standing water, missing vapor barrier, wet insulation or plumbing drips.
  • Indoor humidity. A simple hygrometer shows whether the house is running far outside the 30 to 50 percent range most wood flooring manufacturers ask for.

Fixing a Cupped Floor

The order matters:

  • Find and stop the moisture. Fix the leak, add a vapor barrier in the crawlspace, run a dehumidifier in the basement or get the air conditioning working properly. A plumber or crawlspace contractor may be the first call.
  • Let it dry. Give the wood time to come back into balance with the house, and take moisture readings until they settle.
  • Reassess. Many floors flatten enough on their own that a light sand and refinish, or even nothing at all, is all they need.
  • Sand and refinish if needed. Once the moisture readings are stable, any remaining cupping can be sanded flat and the floor refinished. Hardwood floor sanding explains how we sand a floor flat without taking more wood than necessary.
  • Replace what cannot be saved. Boards that have split, buckled, stayed wet too long or grown mold get cut out and new boards woven in. Wood floor repair covers how those repairs blend in.

Cupping, Gaps and Buckling

These are all moisture problems at different levels. Gaps in winter mean the wood is dry and shrinking, which is normal and seasonal. Mild cupping in a humid summer that eases in fall can also be seasonal. Severe cupping or boards lifting off the subfloor, called buckling, means a lot of moisture and needs attention right away. Why gaps open in winter covers the dry side of the cycle.

Preventing It

  • Keep indoor humidity steady, roughly 30 to 50 percent, with air conditioning or a dehumidifier in summer.
  • Put a vapor barrier down in a dirt crawlspace and keep it intact.
  • Check under the dishwasher, refrigerator and sinks now and then, and fix small leaks quickly.
  • Clean with a barely damp mop, never a soaking one. Hardwood floor cleaning has a routine that works.
  • For new floors, make sure the wood and subfloor are tested and acclimated before installation.

Have It Looked At

If your floor is cupping or crowning, we can take moisture readings, help you find the cause and tell you whether to wait, refinish or repair. We work across the metro, including Kansas City, Shawnee, Lenexa and Blue Springs. See our water damage floor repair and hardwood floor repair services, then get a free estimate.

Get a Free Estimate

Have a floor you want looked at? We give honest, no-pressure estimates across the Kansas City metro.

Good to Know

Why Are My Hardwood Floors Cupping or Crowning? Causes and Fixes in Kansas City: Common Questions

Cupping happens when the bottom of the boards is wetter than the top. Common causes are a damp crawlspace or basement, high summer humidity, plumbing or appliance leaks, and wood installed before it acclimated.

Often, partly or fully, once the moisture source is fixed and the wood dries. That can take weeks or months. Any cupping left after the floor is dry can usually be sanded flat.

Not until it has dried. Sanding a floor while it is still cupped and wet removes the raised edges, and when the wood dries the boards end up crowned, high in the middle. Wait for stable moisture readings first.

Cupping means the edges of each board are higher than the center. Crowning means the center is higher than the edges. Crowning often comes from sanding a cupped floor before it dried out.

Slight seasonal cupping in a humid summer that eases in fall can be normal wood movement. Cupping that keeps getting worse, is concentrated in one area, or comes with buckling points to a moisture problem that needs attention.

Ready for floors you'll be proud of?

Get a free, no-pressure estimate from Kansas City’s trusted hardwood team.